What is a big dresser called?

What is a big dresser called?

Armoire is a French word that refers to any tall, free-standing, ornate cupboard. It may be rectangular or square, narrow or broad. Also known as a wardrobe, this furniture piece is typically bigger and taller than a dresser, and is usually a standing closet used for storing clothes.

What is a short wide dresser called?

The technical dresser definition is a short, wide piece of furniture with multiple drawers in two or more columns with 6 or more drawers. A chest of drawers is a tall, narrow piece of furniture with multiple drawers [Furniture.com]. These days, the two terms are used interchangeably.

Can you add knobs to a dresser?

When you're renovating an old dresser with loose or missing knobs or simply updating the look of your furniture by replacing the hardware, decorative knobs can give the piece an entirely new look.

Can you put legs on a Malm dresser?

Instructions for Adding Legs. Since the bottom of the IKEA Malm dresser is open, first we need to add support pieces to the underside of the dresser that the legs can attach to.

How do you attach furniture legs to a dresser?

How to Add Legs to Furniture

  1. Remove the Skirting. The first thing I did was remove the skirting from the bottom of the dressers and bedside table so that I would have a flat surface to add the furniture legs. ...
  2. Install Leg Mounting Plates. ...
  3. Attach Legs.

Can you add legs to a dresser?

You will need to add legs to a flat surface on the bottom of the dresser. If the bottom isn't flat, you will need to make it so. You can do this by adding a new plywood base. This can either span the full width of the piece or just fit in the corners to provide a surface for adding legs to the dresser.

How do you make a cheap dresser sturdy?

Tighten Up Those Joints and Fixtures. The first and most obvious way to make your furniture a little sturdier is to tighten down the fixtures, screws, and fixtures in all of your furniture.

How do you reinforce drawer bottoms?

Turn the drawer over and squeeze carpenter's glue on the bottom of the drawer. Center the plywood on the bottom of the drawer. Allow the glue to dry overnight. This simple method offers additional stability to the drawer to keep the bottom from sagging.

How do you fix a sagging dresser?

Cut a small block of solid wood or plywood to 3/8 inch thick X 2 inches wide X 4 inches long and glue it to the underside of the drawer bottom. Allow the glue to cure overnight. Next, flip the drawer right-side up and fasten a 1 ½ X 1 ½-inch metal corner brace to the rear center of the drawer.

What can I use for drawer bottoms?

The most common materials for drawer bottoms are 1⁄4" hardboard or plywood. For small and medium-size drawers, hardboard will stand up to a moderate amount of weight. For a heavier load, you can step up to plywood. Baltic birch plywood is a great choice.

Should you glue drawer bottoms?

No reason not to fully glue the plywood bottoms. The solid wood sides have only minor expansion and contraction along their lengths. Thats about the same as you would expect with plywood, only minor expansion and contraction in either direction. Gluing the bottoms will add considerable strength.

How do you fix a dresser drawer that fell off the track?

  1. Pull the drawer out of the desk. ...
  2. Wiggle the tracks with your fingers, and if they move, tighten the screws holding them, using a screwdriver. ...
  3. Reattach the central track to the back of the desk if it has come loose. ...
  4. Reassemble the drawer if it has come apart.

Why do my dresser drawers keep opening?

Most drawers are made up of glides and tracks which are fitted with screws. It is common that these screws can become loose, either on the drawer glides or on the tracks within the cabinet. ... If the glides or tracks slant slightly towards the front of the cabinet, this may cause your drawer to open by itself.

Where should drawer slides be positioned?

I place them so the main part of the slide rests on the face frame. For the slides I use, usually American made K/V 8405, that puts the drawer mount part at 3/4" up (to centerline) from the bottom which allows about 1/8" between the drawer bottom and face frame.

How long do drawer slides need to be?

Drawer Slide Length For side-mount and center-mount slides, typically measure the distance from the front edge of the cabinet to the inside face of the cabinet back and then subtract 1". For under-mount slides, measure the drawer length. Slides must be the same length as drawer to work properly.

How much space do you need for drawer slides?

Most side-mount slides require 1/2” to 17/32” of clearance on each side of a drawer. That means each drawer should be 1” to 1-1/16” smaller than the opening to fit properly. Under-mount slides attach to the bottoms of drawer boxes and can't be seen when the drawers are open.

How deep should dresser drawers be?

The depth of any dresser is approximately 16 to 22 inches. The greater depth provides more stability needed in taller chests or dressers with mirrors attached to them. Drawers pull out 10 to 12 inches for use, so add that measurement to the depth when planning where to place your dresser.

Can drawer slides be shorter than drawer?

Slides come in lengths from 10" to 28". A too-short slide prevents the drawer from opening fully, and one that's too long won't fit in the cabinet.

How wide should a drawer be?

Drawers should not be wider than about 20 inches. Any wider and they become cumbersome and hard to use. If there's too much room in the layout, enlarge one of the cabinet-door openings where you keep pots and pans. Try to balance the width of the cabinet doors and drawers.