What is the best sealer for exposed aggregate?

What is the best sealer for exposed aggregate?

Simply apply a concrete sealer, like the Siloxa-Tek 8500, to the exposed aggregate. The Siloxa-Tek 8500, a water-based silane/siloxane, will act as a salt barrier, penetrating into the concrete substrate in order to provide comprehensive protection from water, UV radiation, cracking, spalling and pitting.

Should you seal exposed aggregate concrete?

Applying a transparent concrete sealer to an exposed aggregate surface can improve both its performance and appearance by helping to protect against spalling, dusting, efflorescence, freeze-thaw damage, stains, deicing salts and abrasion.

How do you clean and seal exposed aggregate concrete?

Wash the exposed aggregate concrete with a concrete cleanser, scrubbing with a nylon brush to remove as much dirt as possible. Rinse with water until all the cleanser is gone. Let the concrete dry completely or almost completely; most sealers work when the concrete is slightly damp, but not soaking wet.

How soon can you seal exposed aggregate?

While it can be tempting to apply driveway concrete sealer right after it is poured, this is never recommended. There is excess moisture in the concrete that needs to evaporate during the curing process. The total curing process normally takes about a month before the concrete is solid and ready to be sealed.

Can you fix exposed aggregate concrete?

The cement in a concrete slab usually holds the surface layer of aggregate in an exposed aggregate slab securely in place. ... To restore the appearance of the slab, you must patch these damaged areas. An epoxy mix, combined with new aggregate, can provide the patch you need.

Is Exposed aggregate concrete expensive?

Stamping is not expensive, but using aggregate concrete is more economical, especially if you have a larger project. Typically, stamped concrete starts at $120 while an exposed aggregate finish is around $100. The pricing will depend on the materials, appearance, contractor, size, and location.

Is Exposed aggregate concrete durable?

Exposed aggregate concrete is not only used for its aesthetic appeal, but it is also durable and skid-resistant, helping to make walkways, driveways, pool decks, and patios safer.

Is Exposed aggregate worth it?

While still incredibly durable, exposed aggregate is more prone to damage than standard concrete and therefore needs to be sealed more often. ... However, if you really love the look of exposed aggregate, then you'll likely find these few extra maintenance tasks to be worth the effort.

Can you pressure wash exposed aggregate?

Use a high pressure washer with hot water and a commercial-grade degreaser to eliminate oil stains. ... Exposed aggregate cleaners can be applied on tire marks before rinsing it off with hot water. Use a stiff-bristled brush to remove extra-stubborn stains prior to rinsing.

How long does Exposed aggregate last?

thirty years

How do I apply exposed aggregate sealer?

Clean and apply After cleaning the concrete, allow a day to dry. Once the concrete is dry, begin the sealing process. Using a ½-inch roller and a pump-up sprayer, start applying the sealer. If the project is a driveway, start by the garage door entrance working toward the road making sure not to step in the sealer.

What happens if you dont seal exposed aggregate?

Intense UV rays from the sun, repeated wet-dry cycles, and periodic freeze-thaw conditions quickly break down even the most durable of clear sealers. Improperly sealed, exposed aggregate concrete driveways often take on a blotchy, dull look after even just one winter.

How much does an exposed aggregate driveway cost?

Expect to pay $50 to $75 per square metre for spray-on concrete, $60 to $85 per square metre for plain concrete, $75 to $90 per square metre for coloured concrete and $100 to $150 per square metre for exposed aggregate or a decorative stencilled finish.

How do you do exposed aggregate?

Using a surface retarderToday, most contractors expose aggregate by spraying a chemical surface retarder onto the slab surface immediately after placing and finishing. This delays the set and gives them the flexibility to remove the cement paste up to a day or so later, either by scrubbing or pressure washing.

What is a cubic Metre of concrete worth?

The average cost of concrete is anywhere from $200 – $300 per m3 (cubic metre), though you could pay as much as $350 for 40 MPa strength. Variations in cost are due to local prices differing slightly, the type of concrete you order, and any additives or admixtures required.

How many wheelbarrows are in a cubic Metre of concrete?

One cubic metre of concrete weighs around 2.

How do you mix 1 cubic meter of concrete?

To make 1 cubic metre of concrete you need to mix 2 tonnes of Sand & Gravel Mix with 16 bags of cement. The recommended cement for mixing concrete is Boral Grey Builders Cement or Boral General Purpose Cement. Sand & Gravel Mix is available by the tonne.

How do you mix 1m3 concrete?

Typically, 1m3 of concrete is made up of 350Kg of cement, 700Kg of sand, 1,200Kg of chippings and 150 Litres of water.

How many 20 kg bags of premixed concrete do you need?

Yield: One 20kg bag will cover an area of 1.

How much does a bag of ready mix concrete cover?

15 cubic feet for every 20 pounds of mix, so a 40-pound bag yields . 30 cubic feet, 60 pounds of concrete mix yields . 45 cubic feet and an 80-pound bag yields .